diff --git a/resources/profiles/Geeetech/machine/Geeetech A10 M 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A10 M 0.4 nozzle.json index 534db2ff795..60c3e09ebec 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A10 M 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A10 M 0.4 nozzle.json @@ -45,7 +45,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A10M：https://www.geeetech.com/wiki/index.php/Geeetech_A10M_3D_printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A10M: https://www.geeetech.com/wiki/index.php/Geeetech_A10M_3D_printer \nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.2 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.2 nozzle.json index 0e926a7de1b..d43cfdca6ab 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.2 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.2 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A10：https://www.geeetech.com/wiki/index.php/Geeetech_A10_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A10: https://www.geeetech.com/wiki/index.php/Geeetech_A10_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.4 nozzle.json index 173744c3ebf..058ffe68de7 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.4 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A10：https://www.geeetech.com/wiki/index.php/Geeetech_A10_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A10: https://www.geeetech.com/wiki/index.php/Geeetech_A10_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.6 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.6 nozzle.json index be6ca7d1460..b8efb4bd8f0 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.6 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.6 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A10：https://www.geeetech.com/wiki/index.php/Geeetech_A10_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A10: https://www.geeetech.com/wiki/index.php/Geeetech_A10_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.8 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.8 nozzle.json index 3173a34ad23..499af44c097 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.8 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A10 Pro 0.8 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A10：https://www.geeetech.com/wiki/index.php/Geeetech_A10_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A10: https://www.geeetech.com/wiki/index.php/Geeetech_A10_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A10 T 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A10 T 0.4 nozzle.json index 3b7c4b53c07..d712d93c14a 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A10 T 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A10 T 0.4 nozzle.json @@ -45,7 +45,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Custom Start G-code\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Custom Start G-code\nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A20 0.2 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A20 0.2 nozzle.json index 42d3b4a3ed2..b6118c97453 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A20 0.2 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A20 0.2 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A20：https://www.geeetech.com/wiki/index.php/Geeetech_A20_3D_printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A20: https://www.geeetech.com/wiki/index.php/Geeetech_A20_3D_printer \nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A20 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A20 0.4 nozzle.json index 12f0982d089..9fc1ff45f4e 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A20 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A20 0.4 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A20：https://www.geeetech.com/wiki/index.php/Geeetech_A20_3D_printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A20: https://www.geeetech.com/wiki/index.php/Geeetech_A20_3D_printer \nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A20 0.6 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A20 0.6 nozzle.json index 833ae55c869..e9250c4cb1f 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A20 0.6 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A20 0.6 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A20：https://www.geeetech.com/wiki/index.php/Geeetech_A20_3D_printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A20: https://www.geeetech.com/wiki/index.php/Geeetech_A20_3D_printer \nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A20 0.8 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A20 0.8 nozzle.json index eafbb567fd8..f335ccac3e1 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A20 0.8 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A20 0.8 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A20：https://www.geeetech.com/wiki/index.php/Geeetech_A20_3D_printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A20: https://www.geeetech.com/wiki/index.php/Geeetech_A20_3D_printer \nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A20 M 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A20 M 0.4 nozzle.json index a8ea97cfaa9..5f99d7861dd 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A20 M 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A20 M 0.4 nozzle.json @@ -45,7 +45,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A20M：https://www.geeetech.com/wiki/index.php/Geeetech_A20M_3D_printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A20M: https://www.geeetech.com/wiki/index.php/Geeetech_A20M_3D_printer \nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A20 T 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A20 T 0.4 nozzle.json index 94b538149a9..fa8ee576824 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A20 T 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A20 T 0.4 nozzle.json @@ -45,7 +45,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Custom Start G-code\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Custom Start G-code\nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A30 M 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A30 M 0.4 nozzle.json index 812e2dbd4c9..bc8487bcf10 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A30 M 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A30 M 0.4 nozzle.json @@ -45,7 +45,7 @@ "retract_lift_below": [ "419" ], - "machine_start_gcode": ";Custom Start G-code\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Custom Start G-code\nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.2 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.2 nozzle.json index 0b384e310da..a16d007ed8b 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.2 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.2 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "419" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A30：https://www.geeetech.com/wiki/index.php/Geeetech_A30_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A30: https://www.geeetech.com/wiki/index.php/Geeetech_A30_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.4 nozzle.json index 78adf6e7516..fc692c72f20 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.4 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "419" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A30：https://www.geeetech.com/wiki/index.php/Geeetech_A30_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A30: https://www.geeetech.com/wiki/index.php/Geeetech_A30_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.6 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.6 nozzle.json index 1eacdb0fff4..2111130d100 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.6 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.6 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "419" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A30：https://www.geeetech.com/wiki/index.php/Geeetech_A30_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A30: https://www.geeetech.com/wiki/index.php/Geeetech_A30_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.8 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.8 nozzle.json index 8c84f30d122..331e02351d1 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.8 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A30 Pro 0.8 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "419" ], - "machine_start_gcode": ";Geeetech official wiki homepage for A30：https://www.geeetech.com/wiki/index.php/Geeetech_A30_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for A30: https://www.geeetech.com/wiki/index.php/Geeetech_A30_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech A30 T 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech A30 T 0.4 nozzle.json index 043ee6830d2..0420dd8c10e 100644 --- a/resources/profiles/Geeetech/machine/Geeetech A30 T 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech A30 T 0.4 nozzle.json @@ -45,7 +45,7 @@ "retract_lift_below": [ "419" ], - "machine_start_gcode": ";Custom Start G-code\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Custom Start G-code\nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM140 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; set bed temp\nM190 S[bed_temperature_initial_layer[initial_no_support_extruder]] ; wait for bed temp\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nT[initial_no_support_extruder] ; Choose initial filament for the first line\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "G1 E-2.5 F2100 ; Retract filament\nG92 E0.0\nG1{if max_layer_z < printable_height} Z{z_offset+min(max_layer_z+30, printable_height+0.2)}{endif} E-1.5 F720 ; Retract and raise Z\nG4 ; wait\nM104 S0 ; Cooldown hotend\nM140 S0 ; Cooldown bed\nM107 ; off fan\nG1 X0 Y100 F3000 ; park print head\nM84 ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech M1 0.2 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech M1 0.2 nozzle.json index 4588189eb0f..34b36036b2b 100644 --- a/resources/profiles/Geeetech/machine/Geeetech M1 0.2 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech M1 0.2 nozzle.json @@ -102,7 +102,7 @@ "retract_lift_below": [ "95" ], - "machine_start_gcode": ";Geeetech M1 official wiki URL：https://www.geeetech.com/wiki/index.php/Geeetech_M1_3D_printer \nM104 S[first_layer_temperature] ; Set Hotend Temperature\nM140 S[first_layer_bed_temperature] ; set Bed Temperature\nM190 S[first_layer_bed_temperature] ; Wait for Bed Temperature\nM109 S[first_layer_temperature] ; wait for Hotend Temperature\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Main Fan\nM300 S2500 P1000 ;Play a short tune\nG1 Z0.28 ;Move Z Axis up little to prevent scratching of Heat Bed\nG92 E0 ;Reset Extruder\nG1 Y3 F2400 ;Move to start position\nG1 X75 E40 F500 ;Draw a filament line\nG92 E0 ;Reset Extruder\n;G1 E-0.2 F3000 ;Retract a little\nG1 Z2.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X70 Y3 Z0.27 F3000 ;Quickly wipe away from the filament line\nG92 E0 ;Reset Extruder", + "machine_start_gcode": ";Geeetech M1 official wiki URL: https://www.geeetech.com/wiki/index.php/Geeetech_M1_3D_printer \nM104 S[first_layer_temperature] ; Set Hotend Temperature\nM140 S[first_layer_bed_temperature] ; set Bed Temperature\nM190 S[first_layer_bed_temperature] ; Wait for Bed Temperature\nM109 S[first_layer_temperature] ; wait for Hotend Temperature\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Main Fan\nM300 S2500 P1000 ;Play a short tune\nG1 Z0.28 ;Move Z Axis up little to prevent scratching of Heat Bed\nG92 E0 ;Reset Extruder\nG1 Y3 F2400 ;Move to start position\nG1 X75 E40 F500 ;Draw a filament line\nG92 E0 ;Reset Extruder\n;G1 E-0.2 F3000 ;Retract a little\nG1 Z2.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X70 Y3 Z0.27 F3000 ;Quickly wipe away from the filament line\nG92 E0 ;Reset Extruder", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors\nM221 S100;Slicer Flow recovery 100%\nM220 S100 ;Set Feedrate recovery 100%\nM204 P3000.00 R3000.00 T3000.00", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech M1 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech M1 0.4 nozzle.json index 0664a96325d..cd1ac09b5d8 100644 --- a/resources/profiles/Geeetech/machine/Geeetech M1 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech M1 0.4 nozzle.json @@ -102,7 +102,7 @@ "retract_lift_below": [ "95" ], - "machine_start_gcode": ";Geeetech M1 official wiki URL：https://www.geeetech.com/wiki/index.php/Geeetech_M1_3D_printer \nM104 S[first_layer_temperature] ; Set Hotend Temperature\nM140 S[first_layer_bed_temperature] ; set Bed Temperature\nM190 S[first_layer_bed_temperature] ; Wait for Bed Temperature\nM109 S[first_layer_temperature] ; wait for Hotend Temperature\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Main Fan\nM300 S2500 P1000 ;Play a short tune\nG1 Z0.28 ;Move Z Axis up little to prevent scratching of Heat Bed\nG92 E0 ;Reset Extruder\nG1 Y3 F2400 ;Move to start position\nG1 X75 E40 F500 ;Draw a filament line\nG92 E0 ;Reset Extruder\n;G1 E-0.2 F3000 ;Retract a little\nG1 Z2.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X70 Y3 Z0.27 F3000 ;Quickly wipe away from the filament line\nG92 E0 ;Reset Extruder", + "machine_start_gcode": ";Geeetech M1 official wiki URL: https://www.geeetech.com/wiki/index.php/Geeetech_M1_3D_printer \nM104 S[first_layer_temperature] ; Set Hotend Temperature\nM140 S[first_layer_bed_temperature] ; set Bed Temperature\nM190 S[first_layer_bed_temperature] ; Wait for Bed Temperature\nM109 S[first_layer_temperature] ; wait for Hotend Temperature\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Main Fan\nM300 S2500 P1000 ;Play a short tune\nG1 Z0.28 ;Move Z Axis up little to prevent scratching of Heat Bed\nG92 E0 ;Reset Extruder\nG1 Y3 F2400 ;Move to start position\nG1 X75 E40 F500 ;Draw a filament line\nG92 E0 ;Reset Extruder\n;G1 E-0.2 F3000 ;Retract a little\nG1 Z2.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X70 Y3 Z0.27 F3000 ;Quickly wipe away from the filament line\nG92 E0 ;Reset Extruder", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors\nM221 S100;Slicer Flow recovery 100%\nM220 S100 ;Set Feedrate recovery 100%\nM204 P3000.00 R3000.00 T3000.00", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech M1 0.6 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech M1 0.6 nozzle.json index 5389c3560e7..bf8f1abb4ae 100644 --- a/resources/profiles/Geeetech/machine/Geeetech M1 0.6 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech M1 0.6 nozzle.json @@ -102,7 +102,7 @@ "retract_lift_below": [ "95" ], - "machine_start_gcode": ";Geeetech M1 official wiki URL：https://www.geeetech.com/wiki/index.php/Geeetech_M1_3D_printer \nM104 S[first_layer_temperature] ; Set Hotend Temperature\nM140 S[first_layer_bed_temperature] ; set Bed Temperature\nM190 S[first_layer_bed_temperature] ; Wait for Bed Temperature\nM109 S[first_layer_temperature] ; wait for Hotend Temperature\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Main Fan\nM300 S2500 P1000 ;Play a short tune\nG1 Z0.28 ;Move Z Axis up little to prevent scratching of Heat Bed\nG92 E0 ;Reset Extruder\nG1 Y3 F2400 ;Move to start position\nG1 X75 E40 F500 ;Draw a filament line\nG92 E0 ;Reset Extruder\n;G1 E-0.2 F3000 ;Retract a little\nG1 Z2.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X70 Y3 Z0.27 F3000 ;Quickly wipe away from the filament line\nG92 E0 ;Reset Extruder", + "machine_start_gcode": ";Geeetech M1 official wiki URL: https://www.geeetech.com/wiki/index.php/Geeetech_M1_3D_printer \nM104 S[first_layer_temperature] ; Set Hotend Temperature\nM140 S[first_layer_bed_temperature] ; set Bed Temperature\nM190 S[first_layer_bed_temperature] ; Wait for Bed Temperature\nM109 S[first_layer_temperature] ; wait for Hotend Temperature\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Main Fan\nM300 S2500 P1000 ;Play a short tune\nG1 Z0.28 ;Move Z Axis up little to prevent scratching of Heat Bed\nG92 E0 ;Reset Extruder\nG1 Y3 F2400 ;Move to start position\nG1 X75 E40 F500 ;Draw a filament line\nG92 E0 ;Reset Extruder\n;G1 E-0.2 F3000 ;Retract a little\nG1 Z2.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X70 Y3 Z0.27 F3000 ;Quickly wipe away from the filament line\nG92 E0 ;Reset Extruder", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors\nM221 S100;Slicer Flow recovery 100%\nM220 S100 ;Set Feedrate recovery 100%\nM204 P3000.00 R3000.00 T3000.00", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech M1 0.8 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech M1 0.8 nozzle.json index a61dc68c06c..b94b0677296 100644 --- a/resources/profiles/Geeetech/machine/Geeetech M1 0.8 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech M1 0.8 nozzle.json @@ -102,7 +102,7 @@ "retract_lift_below": [ "95" ], - "machine_start_gcode": ";Geeetech M1 official wiki URL：https://www.geeetech.com/wiki/index.php/Geeetech_M1_3D_printer \nM104 S[first_layer_temperature] ; Set Hotend Temperature\nM140 S[first_layer_bed_temperature] ; set Bed Temperature\nM190 S[first_layer_bed_temperature] ; Wait for Bed Temperature\nM109 S[first_layer_temperature] ; wait for Hotend Temperature\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Main Fan\nM300 S2500 P1000 ;Play a short tune\nG1 Z0.28 ;Move Z Axis up little to prevent scratching of Heat Bed\nG92 E0 ;Reset Extruder\nG1 Y3 F2400 ;Move to start position\nG1 X75 E40 F500 ;Draw a filament line\nG92 E0 ;Reset Extruder\n;G1 E-0.2 F3000 ;Retract a little\nG1 Z2.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X70 Y3 Z0.27 F3000 ;Quickly wipe away from the filament line\nG92 E0 ;Reset Extruder", + "machine_start_gcode": ";Geeetech M1 official wiki URL: https://www.geeetech.com/wiki/index.php/Geeetech_M1_3D_printer \nM104 S[first_layer_temperature] ; Set Hotend Temperature\nM140 S[first_layer_bed_temperature] ; set Bed Temperature\nM190 S[first_layer_bed_temperature] ; Wait for Bed Temperature\nM109 S[first_layer_temperature] ; wait for Hotend Temperature\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Main Fan\nM300 S2500 P1000 ;Play a short tune\nG1 Z0.28 ;Move Z Axis up little to prevent scratching of Heat Bed\nG92 E0 ;Reset Extruder\nG1 Y3 F2400 ;Move to start position\nG1 X75 E40 F500 ;Draw a filament line\nG92 E0 ;Reset Extruder\n;G1 E-0.2 F3000 ;Retract a little\nG1 Z2.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X70 Y3 Z0.27 F3000 ;Quickly wipe away from the filament line\nG92 E0 ;Reset Extruder", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors\nM221 S100;Slicer Flow recovery 100%\nM220 S100 ;Set Feedrate recovery 100%\nM204 P3000.00 R3000.00 T3000.00", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech Mizar M 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech Mizar M 0.4 nozzle.json index 16ec60ed549..ee642ed612f 100644 --- a/resources/profiles/Geeetech/machine/Geeetech Mizar M 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech Mizar M 0.4 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for MizarM：https://www.geeetech.com/wiki/index.php/Mizar_M \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for MizarM: https://www.geeetech.com/wiki/index.php/Mizar_M \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.2 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.2 nozzle.json index 2b5efe991b7..95449158f38 100644 --- a/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.2 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.2 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for MizarPro：https://www.geeetech.com/wiki/index.php/Geeetech_Mizar_Pro_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for MizarPro: https://www.geeetech.com/wiki/index.php/Geeetech_Mizar_Pro_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.4 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.4 nozzle.json index 0f5d9001e4d..d5eb650dd01 100644 --- a/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.4 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.4 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for MizarPro：https://www.geeetech.com/wiki/index.php/Geeetech_Mizar_Pro_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for MizarPro: https://www.geeetech.com/wiki/index.php/Geeetech_Mizar_Pro_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.6 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.6 nozzle.json index 3275ab1e259..ea2561bfd37 100644 --- a/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.6 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.6 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for MizarPro：https://www.geeetech.com/wiki/index.php/Geeetech_Mizar_Pro_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for MizarPro: https://www.geeetech.com/wiki/index.php/Geeetech_Mizar_Pro_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.8 nozzle.json b/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.8 nozzle.json index 73a5a92cbd3..95b845221c5 100644 --- a/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.8 nozzle.json +++ b/resources/profiles/Geeetech/machine/Geeetech Mizar Pro 0.8 nozzle.json @@ -33,7 +33,7 @@ "retract_lift_below": [ "259" ], - "machine_start_gcode": ";Geeetech official wiki homepage for MizarPro：https://www.geeetech.com/wiki/index.php/Geeetech_Mizar_Pro_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", + "machine_start_gcode": ";Geeetech official wiki homepage for MizarPro: https://www.geeetech.com/wiki/index.php/Geeetech_Mizar_Pro_3D_Printer \nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nM220 S100 ;Reset Feedrate\nM221 S100 ;Reset Flowrate\nG92 E0 ; Reset Extruder\nG28 ; Home all axes\nM107 ;Off Fan\nG1 Z5.0 F3000 ;Move Z Axis up little to prevent scratching of Heat Bed\nG1 X0.1 Y20 Z1.4 F6000 ; Move to start position\nG1 X0.1 Y80.0 Z1.4 F1000 E25 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X0.4 Y80.0 Z1.4 F6000 ; Move to side a little\nG1 X1.4 Y20 Z1.4 F1000 E20 ; Draw the second line\nG92 E0 ; Reset Extruder\nG1 Z2.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X5 Y20 Z0.28 F3000.0 ; Move over to prevent blob squish\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{z_offset+min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{z_offset+min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < max_print_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", "nozzle_type": "brass", "auxiliary_fan": "0" diff --git a/resources/profiles/Geeetech/machine/fdm_geeetech_common.json b/resources/profiles/Geeetech/machine/fdm_geeetech_common.json index 7cf74c4dea4..6d69b3828c9 100644 --- a/resources/profiles/Geeetech/machine/fdm_geeetech_common.json +++ b/resources/profiles/Geeetech/machine/fdm_geeetech_common.json @@ -132,7 +132,7 @@ ], "machine_start_gcode": "G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM140 S[bed_temperature_initial_layer] ; set final bed temp\nM104 S150 ; set temporary nozzle temp to prevent oozing during homing\nG4 S10 ; allow partial nozzle warmup\nG28 ; home all axis\nG1 Z50 F240\nG1 X2 Y10 F3000\nM104 S[nozzle_temperature_initial_layer] ; set final nozzle temp\nM190 S[bed_temperature_initial_layer] ; wait for bed temp to stabilize\nM109 S[nozzle_temperature_initial_layer] ; wait for nozzle temp to stabilize\nG1 Z0.28 F240\nG92 E0\nG1 Y140 E10 F1500 ; prime the nozzle\nG1 X2.3 F5000\nG92 E0\nG1 Y10 E10 F1200 ; prime the nozzle\nG92 E0", "machine_end_gcode": "{if max_layer_z < printable_height}G1 Z{min(max_layer_z+2, printable_height)} F600 ; Move print head up{endif}\nG1 X5 Y{print_bed_max[1]*0.8} F{travel_speed*60} ; present print\n{if max_layer_z < printable_height-10}G1 Z{min(max_layer_z+70, printable_height-10)} F600 ; Move print head further up{endif}\n{if max_layer_z < printable_height*0.6}G1 Z{printable_height*0.6} F600 ; Move print head further up{endif}\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors", - "layer_change_gcode": ";------------------------------------\n;layer No：[layer_num] ———>Print Height：[layer_z] mm\n;------------------------------------", + "layer_change_gcode": ";------------------------------------\n;layer No: [layer_num] ———>Print Height: [layer_z] mm\n;------------------------------------", "scan_first_layer": "0", "nozzle_type": "undefine", "support_multi_bed_types": "1",