1) When the wizard is initialized, filament and SLA profile names
are verified and current names of renamed profiles are resolved.
Fixes "Add/Remove Filaments is not hiding all of the un-checked filaments #3835"
2) When adding a printer model, default materials are installed in case
the printer model has no default material installed.
3) When leaving the Filaments or SLA materials page, and some printer models
have no material installed, those Printer Models are listed
in a message box and only for those printer models the default
materials are installed.
This reverts commit 3d3e36ba8d.
The change is too risky just before the PrusaSlicer 2.2.0 final release
and the feature may need a bit of polishing before release.
the "renamed_from" property of current profiles was not taken into account.
This lead to a situation where there were no MMU or SLA materials installed
after upgrade from PrusaSlicer 2.2.1 to 2.2. This should work now.
and the "show incompatible profiles" option.
It was not able to select the incompatible Print profile, which is
possible now.
(see Cannot select incompatible printer profile #3715)
When the Printer profile derived from the Prusa3D system profile was
active or a system Prusa3D profile was active, and when the Print profile
with the removed "inherits" field was active (or any other profile
derived from the "-- default --" profile was active), then the filament
selector offered just the profiles with the removed "inherits" field
(or any other profile derived from the "-- default--") profile.
This behavior has been now changed, so that in this scenario the Filament selector
will offer the Prusa3D vendor profiles compatible with the active Print
and Printer profile as well as the user profiles.
Slicer was also changed to keep an incompatible preset selected
at its respective tab if its respective "Red flag" is enabled.
For example, if an incompatible Print preset is selected and a Printer
profile is switched to another one which is not compatible with the active
Print preset that was red already, the active Print preset is
not switched if the Print "Red flag" is active. However, if the Print profile
was compatible before the Printer profile is switched and now the Print
profile becomes incompatible, another compatible Print profile is selected.
A likely bug in wxWidgets was worked around when switching a Print preset
on Plater, if the last item in the Print preset was active and incompatible,
and another Print preset was selected by the user. On Windows, an CBN_EDITCHANGE
is sent just after combo box selection change event and the CBN_EDITCHANGE
holds an index of the combo box item, which will be removed by the 1st event,
therefore leading to an assert in wxWidgets on CBN_EDITCHANGE. The workaround
is to disable processing of CBN_EDITCHANGE on Windows for the Plater
preset selection combo boxes.
Opening saved project removes Print Host settings #3655
Octoprint Settings when Opening a .3MF file #3244
When loading a configuration file (from AMF, 3MF, .ini or .gcode),
and if the host settings ("print_host", "printhost_apikey", "printhost_cafile")
in the configuration file is empty, then the config is considered to be anonymized,
and these anonymized keys are loaded from the referenced "derived from" profile,
if it exists in user's PrusaSlicer configuration directory.
We are aware that this is a patch work and a better long term solution
is to separate physical printer settings from logical printer settings,
but this is a good enough solution for PrusaSlicer 2.2.0 release.
The two new config keys define a minimum vertical shell thickness.
The top shell thickness is calculated as a maximum of sum over
top_solid_layers * layer heights and top_solid_min_thickness,
the bottom shell thickness is calculated as a maximum of sum over
bottom_solid_layers * layer heights and bottom_solid_min_thickness.
The results of the formula above are shown at the Print parameter page
below the two new values to hint the user about the interaction
of the old versus new config values.
top_solid_min_thickness has no meaning if top_solid_layers is zero,
bottom_solid_min_thickness has no meaning if bottom_solid_layers is zero.
which now will be used for preset choosers on sidebar a preset tabs.
+ for BitmapCache class added m_scale used for correct scaling of SVG images on Retina displays
+ some code clearing from unused functions or function's parameters
so that references from user profiles and .3mfs / .amfs
to system profiles are not being lost.
If a system profile has no "renamed_from" profile name assigned,
and the system profile name contains "@", then a profile name
with the "@" is implicitely assumed to be the name, from which this
profile has been renamed.
Step to repro:
1. Select system "Some_preset" preset
2. Make some changes
3. Save preset with "Some_preset - Copy" name.
=> "Some_preset - Copy" is selected, there is/are marked option(s) only different from system preset.
repeate 1-3 steps
=> "Some_preset - Copy" is selected, there is/are marked option(s) different from DEFAULT preset.
