Fixes Solid infill where there should be none #6482
Also the safety offsetting was revised to be enabled only where needed,
the "do safety offset" is now easy to discover by
a new ApplySafetyOffset::Yes enum, and safety offset over union, which
is better done by offset() / offset_ex() has been replaced with
new union_safety_offset() / union_safety_offset_ex() functions, which
better convey their meaning and which could be better optimized than
union() with the safety offset applied.
1) If "support on build plate only" is enabled, the support columns are
newly trimmed to not land on top of an object. However this may make
the column too small to be stable.
2) Support enforcers newly take precedence over "supports on build plate only"
and over "don't support bridges".
3) Some refactoring of the support generator code for clarity: Reduced
some of the worst spagetti offenders.
Fixes Support generated even if support on build only activated #915
Fixes Bug: supports on build plate only #1340
Fixes Bottom interface layer is not generated , support on build plate only. (long open defect) #4199
Fixes option "supports on build plate only" does not work #3980
Fixes No support interface layers generated #1997
Fixes Feature Request: Option to combine results of 'support from build plate only' and 'support enforcers only' #2801
Fixes Support interface isn't generated: build plate only + blocked by model + support enforcer #3831
Fixes Support Enforcer don't create interface layers #5748
Fixes Support Enforcers Don't Have Top Loops/Raft #1870
Fixes Don't cancel support enforcers with "don't support bridges" #5105
Adjustment of GUI/3DBed.cpp,hpp to use the more stable triangulation algoritm
derived from SGI glut.
Fix of an extremely slow bridging calculation, caused by an extremely
slow bridged area detection function, of which the results were never used.
Fixes "slicing fails or takes too long #5974"
(non-spiral vase layers) were being closed.
Fixes Bad slicing in vase mode (unexpected bridge and solid infill layers) #3326
Fixes Model with holes in the base does not slice properly in "Vase Mode" #5359
The offset curve extractor is already quite usable,
though singular cases are still not covered yet
when the offset curve intersects or nearly intersects
a Voronoi vertex.
Removal of the PRINTF_ZU "%zu" Visual Studio printf compatibility macro.
Fixes of a contours self intersection test for collinear segments.
SVG exporter now exports white background, so that the GNOME Eye viewer is usable.
Fixes Connecting / expanding Bottom Layers to Vase Perimeter #253
Fixes Slicing error in vase mode #452
Fixes Slicing Issue (Vase Mode, 0.6mm dmr nozzle) #1887
Fixes Top fill pattern isn't used in spiral vase mode #2533
Fixes Cisar's vase doesn't slice correctly, creates artefacts #3595
When the model is sliced, all the contours are newly oriented
counter-clockwise (even holes), merged and then only the largest area
contour is retained. In perimeter generator, if the largest contour
splits into multiple perimeters, newly only the largest area perimeter
is retained in spiral vase mode. These two changes solve #3595 and similar.
The infill is newly calculated only for the bottom solid layers
if the spiral vase mode is active (removes various unwanted infill
along the vase walls), and the last bottom solid layer is switched
to a top solid pattern (solves #2533).
The thin walls are newly enforced to be disabled in spiral vase mode,
and the "ensure vertical shell wall" is enforced in spiral vase mode
to extend the bottom of the vase to the vase hull (fixes#253).
If the Elephant foot compensation is applied to the 1st object's layer,
the uncompensated 1st object's slice is newly used for calculation
of bridges, overhans, skirt, brim, raft and supports.
Layer::slices were renamed to Layer::lslices to simplify reading
of the code, to differentiate from LayerRegion::slices.
Reworked the FFF testing framework & ConfigBase::set_deserialize()
for more compact tests: set_deserialize() now accepts list
of key / value pairs.
Fixed an incorrect assert in LayerRegion.
Layer newly remembers bounding boxes of slices,
the bounding boxes are used by G-code generator & newly the support
generator.
Slices are stored as ExPolygons, not ExPolygonCollection.
Fix of "Bridging infill not connecting with infill set to 0%" #1301
Top, bottom and bridging areas are extended into infill as long
as the infill is not zero. If the infill is zero,
top, bottom and bridging areas wound not expand into these "void" areas.
With this commit, the top, bottom and bridging areas are allowed to expand
into the "void" areas as long as these "void" areas are supported below
with perimeters or some other non-empty infill, and slightly beyond
these supporting areas into the voids (currently hard coded to 1mm).
In case the bridge is only supported at one side, it is technically
not considered to be a support, therefore the default infill angle is used.
With this change, the bridging areas use the custom angle value even
if not supported on both sides.
