Made small performance, safety, and readability improvements.
Now the logic is only called to move the build plate lower than the tallest object if the print_sequence is, "by object".
More precise checks to not move the plate beyond the maximum build volume.
* Bump Elegoo profile version to refresh installed bundle
Bumps the Elegoo vendor profile version so installed profile bundles are refreshed from bundled resources after the recent Elegoo profile sync.\n\nThe previous version stayed at 02.04.00.00 after the profile layout changed, so existing installs could keep loading stale system/Elegoo files. That stale bundle can abort during profile loading and cause user presets inheriting from Elegoo machines, such as OrangeStorm Giga and Neptune 3 Max, to report missing parents.\n\nValidation:\n- jq parsed resources/profiles/Elegoo.json\n- verified all Elegoo.json sub_path entries exist\n- git diff --check
* Fix Elegoo process profile manifest
* Fix: Disable redundant toolchange retraction for Elegoo Centauri Carbon
Sets `retract_length_toolchange` to 0 in the Elegoo Centauri Carbon (ECC) machine profile.
This resolves an issue where a massive filament blob would form on the prime tower immediately after resuming a manual filament change (M600). The blob was caused by a conflict between OrcaSlicer's default toolchange logic and Elegoo's hardcoded firmware behavior:
- Elegoo's firmware (specifically the `cmd_PAUSE` and `cmd_RESUME` sequences) completely takes over pressure management during an M600. It performs its own initial 2mm retraction, a 120mm purge, and a silicone brush wipe, returning the print head to the prime tower perfectly primed.
- Previously, Slicer was unaware of the firmware's priming and would issue a redundant 2mm un-retract (`G1 E2`) upon resume. Forcing 2mm of filament out of an already-full nozzle created the blob.
By disabling the toolchange retraction (`0`), Slicer correctly hands off filament pressure management during an M600 entirely to the Elegoo firmware, preventing double-retractions and eliminating the blob.
* fix errors after merging main
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
* Update the stealth mode description to reflect the current code changes in 2.4.
* disable HMS if bambu network plugin is not installed or in stealth mode
* fix build err
* add hide_login_side_panel to control whether to show login panel in home page
* Support 'Default' filament option (index 0)
Treat filament index 0 as the new "Default" (use active object/part filament) instead of using 1. Update config defaults and tooltips for wall/sparse/solid infill filament options (min/default -> 0, tooltip explains "Default"). Adjust normalization and propagation logic to respect explicit feature overrides and only apply base extruder when feature values are zero; only copy sparse->solid infill when sparse > 0. Introduce FeatureFilamentOverrideMask and clamp_feature_filament_to_valid to resolve and clamp feature filaments. Update UI lists and selection behavior to expose a "Default" entry and handle zero-based indices in PartPlate and Plater.
* enable_filament_for_features option
Co-Authored-By: LixNix <105106115+lixnix@users.noreply.github.com>
* \n
* Allow wipe_tower_filament to equal nozzle count
Relax the assertion in Print::extruders to permit wipe_tower_filament == config().nozzle_diameter.size(). The configuration value is 1-based and the code subtracts 1 when pushing the extruder index, so equality should be valid and selecting the last nozzle should not trigger an assertion.
* Revert "Allow wipe_tower_filament to equal nozzle count"
This reverts commit 2c976574327a8bcdc74a1b296bf1aaff7752a94e.
* Revert "enable_filament_for_features option"
This reverts commit 01c13baeddb8e26793f752deab788ee4d086975b.
* Migrate legacy feature filament defaults
Add migration logic to convert legacy feature filament selections from 1 to 0 for older 3mf files. Introduces a local migrate_legacy_feature_filament_defaults lambda in src/OrcaSlicer.cpp and src/slic3r/GUI/Plater.cpp that scans keys (wall_filament, sparse_infill_filament, solid_infill_filament, support_filament, support_interface_filament) on configs/objects/volumes, updates values, counts conversions and logs the result. Also adds a Semver check for "2.4.0-dev" in OrcaSlicer to trigger the migration for files older than that version. This preserves expected default filament selections when loading older project files.
* Update OrcaSlicer.cpp
* Extract migration helper to ConfigMigrations
Centralize legacy feature-filament default migration by moving the duplicated lambda into ConfigMigrations::migrate_legacy_feature_filament_defaults (src/libslic3r/Config.cpp) and declaring it in Config.hpp. Update OrcaSlicer.cpp and slic3r/GUI/Plater.cpp to call the new function instead of inline lambdas. The helper converts specific feature filament keys (wall_filament, sparse_infill_filament, solid_infill_filament, support_filament, support_interface_filament) from int 1 to 0 and returns the count of conversions to avoid duplicated migration logic.
* Remove DynamicFilamentList1Based and consolidate lists
Delete the specialized DynamicFilamentList1Based struct and its global instance. Update Choice registrations to use the single dynamic_filament_list for wall, sparse_infill and solid_infill filaments, and remove the extra update call for the removed instance. This consolidates filament choice handling and removes duplicated logic in Plater.cpp.
* move it
* fix objects
* Update Config.hpp
* Update profiles
* fix(ElegooLink): pass printer SN to CC2 device panel URL
The CC2 panel subscribes to MQTT topics keyed by the printer serial number.
Without sn= in the URL it uses a wrong hardcoded fallback SN, subscribes to
the wrong topics, and shows Offline permanently even though the printer is
reachable.
- Cache the SN in elegoo_cc2_test() (already fetches it, was discarding it)
- Look up cache in get_print_host_webui(); fall back to a short LAN HTTP
call on first use before the test has run
- Append sn= to the panel URL
- Clear the wrong hardcoded fallback SN/IP from the panel bundle
- Add a small synchronous boot script to the panel that fetches the SN
from the printer before the bundle reads URLSearchParams, as a fallback
for unpatched binaries
* fix(ElegooLink): persist CC2 serial number in AppConfig dev_sn section
Store the printer SN under [dev_sn] keyed by normalized print_host after
a successful connection test or system/info fetch. Reuse it on later
sessions before hitting the network, matching how access_code is keyed by
dev_id for other LAN printers.
* fix(ElegooLink): answer get_sn IPC instantly from dev_sn cache
The CC2 panel always calls get_sn with a 10s timeout. Remove the HTTP
fallback from get_sn() and resolve IPC from dev_sn/memory only so Device
tab load is not blocked after sn= is already in the URL.
* fix(ElegooLink): skip get_sn IPC when URL already has sn
The CC2 device panel calls get_sn with a 10s timeout on every MQTT
connect even when Orca passes sn= in the query string. Use the URL
serial immediately and only fall back to IPC when it is missing.
* refactor(ElegooLink): resolve CC2 SN via PrintHost::get_sn in GUI
Drop the ElegooLink.hpp include from PrinterWebViewHandler; the webview
IPC handler uses the existing PrintHost virtual instead. Keep CC2 serial
lookup helpers file-local in ElegooLink.cpp and share them between
get_sn() and get_print_host_webui().
* chore: drop redundant <memory> include in PrinterWebViewHandler
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
Consolidates #13744 (CFS filament sync) into this PR per maintainer
request and resyncs with main. Conflicts resolved:
* src/slic3r/GUI/Plater.cpp -- parallel else-if added by both sides
(htCrealityPrint + flashforge_local_api branches); kept both.
* src/slic3r/GUI/PhysicalPrinterDialog.cpp -- both sides added a
host-specific Browse dialog (Creality DNS-SD + Flashforge); kept
both as early-return branches, fall through to BonjourDialog.
* src/slic3r/GUI/PrintHostDialogs.hpp -- parallel class declarations
(CrealityPrintHostSendDialog + FlashforgePrintHostSendDialog);
kept both.
* Update/add re:3D profiles.
* Fix encoding issue with UTF-8 BOM
* Change spaces to tabs.
* Fix alignment-based space indentation issues.
* Test: rename_from property
* Test 2: rename_from property
* Test 3: use 'renamed' instead of 'rename'
* Add renamed property for each conflicting profile.
* Revert to optimized assets improved on [#13149](https://github.com/OrcaSlicer/OrcaSlicer/pull/13149)
* Sync Elegoo profiles from ElegooSlicer
Update vendor Elegoo.json, filament/machine/process trees, and OrcaFilamentLibrary
Elegoo entries. Align machine default material names with existing filament preset names.
* feat: expose filament_name for G-code export filename format
Derive from filament_settings_id for the first active extruder and strip the suffix after @, matching ElegooSlicer so filename_format can use {filament_name}.
* chore: reorder Elegoo entries in OrcaFilamentLibrary
Group Elegoo @base profiles and bump library version to 02.03.02.62.
* sync OrcaFilamentLibrary.json with Elegoo filament profiles
* fix: clean up Elegoo process renamed_from for profile validation
Add single renamed_from only where preset names changed from legacy Orca
names; remove duplicate Rapid @System library entries that conflicted with
ECC2 vendor presets.
* fix(profiles): add missing Elegoo renamed_from for profile validation
CI custom-preset tests still inherit legacy Orca preset names that no
longer exist after the Elegoo bundle update. Add renamed_from on process,
Neptune 4 machines, OrcaFilamentLibrary filaments, and Giga profiles so
inherits resolve again, without changing print parameters.
Update Snapmaker U1 (0.4 nozzle).json
Updated Snapmaker U1 0.4 nozzle "change_filament_gcode" and "machine_end_gcode" to fix the issue of collisions when using "Print by Object"
PR #13388 added resources/printers/N6.json for X2D support but did not
bump resources/printers/version.txt. PresetUpdater only copies files
from the install's resources/printers/ to the user's data_dir/printers/
when the resources version is newer than the user's stored version, so
every existing install stays at 02.00.00.29 and never receives N6.json.
At runtime, json_diff::load_compatible_settings("N6", "") reads from
data_dir/printers/N6.json; the silent file-missing failure leaves
is_support_bed_leveling, is_support_pa_calibration, and
SupportCalibrationNozzleOffset at their defaults, hiding the Bed
Leveling and Nozzle Offset Calibration checkboxes in the Send Print
Job dialog for the X2D.
Bumping the patch version triggers the existing propagation logic on
next startup.
Fixes#13780Fixes#13794
Co-authored-by: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
The fdm_filament_petg base template added in 7f46c652 (cherry-picked
from hamham999's PR 13581) had two bugs:
- filament_type: ["PLA"] (should be PETG)
- inherits: null (should chain to fdm_filament_common)
so OrcaSlicer still rejected our CR-PETG profiles even after the
base was installed.
The existing fdm_filament_pet base already declares filament_type:
["PETG"] and inherits fdm_filament_common, so it correctly serves as
the PETG base. Repoint all 10 K2-family CR-PETG profiles at it and
remove the buggy fdm_filament_petg.json + its Creality.json entry.
This effectively reverts the resource addition from 7f46c652 while
keeping the CR-PETG filament profile additions from 5612e120 (now
with a working inherits chain).
Verified locally: OrcaSlicer parses all 10 profiles without error and
the K2 family populates the Add Printer dialog.
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
The 10 CR-PETG profiles added in 5612e120 (also from hamham999s PR
13581) inherit from fdm_filament_petg, but that base template did
not exist in the Creality profile set - only fdm_filament_pet. Result:
OrcaSlicer logged
can not find inherits fdm_filament_petg for CR-PETG @Creality K2...
and aborted the rest of the Creality filament load, leaving the
filament dropdown empty for K2 users.
Adds the base template (originally added in hamham999s PR 13581) and
registers it in Creality.json filament_list after fdm_filament_pet.
Reported-by: local testing on Hark Tech 2026-05-21 test build.
Co-Authored-By: hamham999 <hamham999@users.noreply.github.com>
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
Two follow-ups from #13744 review:
1. K2 firmware payloads reference "CR-PETG" by name (per DaviBe92's
reverse-engineering work in k2-websocket-re, and a real Creality spool
seen by @swilsonnc), but the profile was missing from the Creality
filament set. Adds 10 K2-family variants:
- K2: 0.4, 0.6, 0.8 nozzles
- K2 Plus: 0.2, 0.4, 0.6, 0.8 nozzles
- K2 Pro: 0.4, 0.6, 0.8 nozzles
Profile values come from CrealityPrint v7.1.0 via @hamham999's
parallel work in OrcaSlicer/OrcaSlicer#13581. Files re-indented with
tabs and BOM stripped to match repo convention.
2. Creality HF Generic PLA and Creality HF Generic Speed PLA were missing
filament_vendor: ["Creality"] so they appeared under "General" rather
than "Creality" in the filament selector.
Reported-by: swilsonnc, DaviBe92 (CR-PETG missing)
Co-Authored-By: hamham999 <hamham999@users.noreply.github.com>
Co-Authored-By: Claude Opus 4.7 (1M context) <noreply@anthropic.com>
fix: OK/Cancel buttons clipped in Flushing Volume dialog (#13511)
The WipingDialog renders its UI inside a wxWebView. When the dialog
was clamped to screen size (many filaments, small displays, high DPI),
the HTML content exceeded the WebView bounds and the OK/Cancel buttons
fell below the visible area.
HTML fix:
- Convert .container to flexbox column with overflow-y: auto
- Pin .button-container with flex-shrink: 0 so it stays visible
- Allow .scroll-container to flex-grow for the table area
C++ fix:
- Replace heuristic extra_size with accurate fixed_overhead estimate
- Use correct cell height (25 DIP) matching HTML table row height
- Add screen margin for window decorations
- Enforce minimum dialog size when clamped
Co-authored-by: SoftFever <softfeverever@gmail.com>
CI flagged ~150 K2 profile files for using space indentation; repo convention
is tab indentation. Ran the upstream-provided fixer:
python3 scripts/orca_filament_lib.py -v Creality -p filament -f --force
Mechanical normalization:
- Spaces → tabs (1 tab per indent level)
- Field ordering normalized (name + type first)
- Single-value scalar fields converted to single-element arrays where the
schema expects arrays (filament_cost, filament_density,
temperature_vitrification, filament_max_volumetric_speed)
No semantic content changes. Pre-existing issue from the original K2
profile import; touching these files in the multicolor_method strip
brought them into the validator's PR-diff scope.
Two data-only fixes:
#1 Strip undefined {if !multicolor_method} wrapper from filament_start_gcode on 110 K2-Plus profiles. The placeholder is a CrealityPrint-ism that survived the profile port; Orca has no such variable, so slicing failed with a hard parser error (reported on Hyper PLA by u/Gullible-Price-4257). Inner per-layer temp logic now runs unconditionally, which is the correct default.
#4 Add filament_vendor: [Creality] to 50 Creality Generic profiles missing the field. Without it the UI grouped them under Generic instead of Creality (reported by u/mharrop94).
Import 191 brand-specific filament presets for the K2 family of
printers (K2, K2 Plus, K2 Pro), lifted from
CrealityOfficial/CrealityPrint v7.1.1 under AGPL-3.0 (compatible
with OrcaSlicer AGPL-3.0).
Brand coverage:
CR-series: CR-PLA, CR-PLA Matte, CR-PLA Fluo, CR-Silk,
CR-TPU, CR-ABS, CR-Nylon
Hyper-series: Hyper PLA, Hyper PLA-CF, Hyper ABS, Hyper PA-CF,
Hyper PA6-CF, Hyper PAHT-CF, Hyper PA612-CF,
Hyper PC, Hyper Marble, Hyper Stardust,
Hyper L-W PLA, Hyper PPA-CF
Third-party: eSUN PLA+ / PLA-HS / PLA-Matte / PLA-Silk /
PLA-CF / PLA-LW / PLA-Lite, PolySonic PLA /
PLA Pro, Panchroma PLA Matte / Satin, Soleyin
Ultra PLA, HP Ultra PLA, HP-ASA, HP-TPU
Ender PLA variants and CrealityPrint per-K2 Generic versions of
PLA, ABS, ASA, PA, PA-CF, PAHT-CF, PET, etc.
This closes the matching gap exposed by the CFS filament-sync
work. When the K2 reports spool brand Hyper PLA or CR-PLA, the
existing Creality vendor only had a generic Creality Generic PLA
@K2-all preset to fall back to, so per-brand temps / PA / cooling
tuning was lost on every sync.
Schema and naming are drop-in compatible -- CrealityPrint
references the K2/K2 Plus/K2 Pro machine names already present in
OrcaSlicer Creality vendor (Creality K2 0.4 nozzle, etc), so no
machine-side changes or compatible_printers rewrites are required.
K2 SE filaments and the PETG/PP/PPS/HIPS family are deferred. K2
SE machine profile is not yet in OrcaSlicer Creality vendor, and
the PETG/PP/PPS/HIPS family relies on fdm_filament_* base
templates that do not exist in Orca Creality vendor -- importing
those bases from CrealityPrint did not make them register as valid
parents at preset-load time. Coverage for the missing families
will land in a follow-up once the loader requirements for new
bases are understood.
Vendor version bumped to 02.03.02.75 to trigger the per-user
profile refresh on next launch. Source attribution captured in
resources/profiles/Creality/NOTICE.md.
* Expose Antialiasing velues
Expose Antialiasing multipliers.
Default to 4 as current implementation but enables the user to disable it to improve performante or increase sampling to improve quality.
* FXAA
* Improve descriptions
* Require restart when MSAA setting changes
Detect changes to the OpenGL MSAA (multisample anti-aliasing) preference when opening Preferences and prompt the user to restart the application to apply the change. Adds a constant key for the MSAA setting, stores the previous value, checks for changes (similar to the existing FXAA handling), and shows a warning dialog explaining the restart will close the current project without saving. If the user accepts, recreate_GUI is invoked to apply the MSAA change immediately.
* Revert "Require restart when MSAA setting changes"
This reverts commit dde134d346c3849598c91d025d2faed1b51c8a22.
* Menu and FPS options
* Fix FPS limiter and remove VSYNC
* Grouped FPS settings and mode up rigth fps counter
---------
Co-authored-by: Noisyfox <timemanager.rick@gmail.com>
