{
	"type": "machine",
	"setting_id": "GM_Anycubic_001",
	"name": "Anycubic 4Max Pro 2 0.4 nozzle",
	"from": "system",
	"instantiation": "true",
	"inherits": "fdm_machine_common",
	"printer_model": "Anycubic 4Max Pro 2",
	"default_print_profile": "0.20mm Standard @Anycubic 4MaxPro2",
	"extruder_type": [
		"Bowden"
	],
	"nozzle_diameter": [
		"0.4"
	],
	"printable_area": [
		"0x0",
		"270x0",
		"270x210",
		"0x210"
	],
	"printable_height": "190",
	"retract_lift_below":[
		"189"
	],
	"nozzle_type": "undefine",
	"auxiliary_fan": "0",
	"machine_max_acceleration_extruding": [
		"1250",
		"1250"
	],
	"machine_max_acceleration_retracting": [
		"1250",
		"1250"
	],
	"machine_max_acceleration_travel": [
		"1500",
		"1500"
	],
	"machine_max_acceleration_x": [
		"900",
		"900"
	],
	"machine_max_acceleration_y": [
		"900",
		"900"
	],
	"machine_max_acceleration_z": [
		"100",
		"100"
	],
	"machine_max_speed_e": [
		"120",
		"120"
	],
	"machine_max_speed_x": [
		"200",
		"200"
	],
	"machine_max_speed_y": [
		"200",
		"200"
	],
	"machine_max_speed_z": [
		"16",
		"16"
	],
	"machine_max_jerk_e": [
		"5",
		"5"
	],
	"machine_max_jerk_x": [
		"6",
		"6"
	],
	"machine_max_jerk_y": [
		"6",
		"6"
	],
	"machine_max_jerk_z": [
		"0.2",
		"0.2"
	],
	"max_layer_height": [
		"0.3"
	],
	"min_layer_height": [
		"0.07"
	],
	"printer_settings_id": "Anycubic",
	"retraction_minimum_travel": [
		"2"
	],
	"retract_before_wipe": [
		"0%"
	],
	"retraction_length": [
		"2.5"
	],
	"retract_length_toolchange": [
		"10"
	],
	"retraction_speed": [
		"35"
	],
	"deretraction_speed": [
		"25"
	],
	"single_extruder_multi_material": "0",
	"change_filament_gcode": "M600",
	"machine_pause_gcode": "M601",
	"default_filament_profile": [
		"Generic PLA @Anycubic"
	],
	"machine_start_gcode": "G21 ; metric values\nG90 ; absolute positioning\nM82 ; set extruder to absolute mode\nM140 S[first_layer_bed_temperature] ; set bed temp\nG28 X0 Y0 ; home X and Y\nG28 Z0 ; home Z\nG1 Z30 F{machine_max_speed_z[0]*60} ; move Z a bit down to not blow on the bed edge while heating\nG1 X10 F3900 ; let some space on x to prevent the filament cooling exhaust from beeing blocked by the servo motor\nM190 S[bed_temperature_initial_layer_single] ; wait for bed temp\nM104 S[nozzle_temperature_initial_layer] ; set extruder temp\nM106 S80 ; turn on fan to prevent air nozzle melt while heating up\nM109 S[nozzle_temperature_initial_layer] ; wait for extruder temp\nM107 ; start with the fan off\nG28 X0 ; goto X home again\nG92 E0 ; zero the extruded length\nG1 Z0.2 F360 ; move plattform upwards\n; extrude material next to the plattform (comment or remove following lines to disable)\nG1 F180 E20 ; extrude some material next to the plattform\nG92 E0 ; zero the extruded length\nG1 E-[retraction_length] F{retraction_speed[0]*60} ; do a filament retract\nG92 E0 ; zero the extruded length again\nG1 X5 F3900 ; move sideways to get rid of that string\nG1 E[retraction_length] F{retraction_speed[0]*60} ; do a filament deretract with retract parameters\nG92 E0 ; zero the extruded length again\n; draw intro line (comment or remove following lines to disable)\nG1 X30 E5 F700 ; draw intro line\nG92 E0 ; zero the extruded length\nG1 E-[retraction_length] F{retraction_speed[0]*60} ; do a filament retract\nG1 X40 Z2.0 ; move away from the introline\nG92 E0 ; zero the extruded length again\nG1 E[retraction_length] F{retraction_speed[0]*60} ; do a filament deretract with retract parameters\n; end of intro line code\nM117 Printing...\nG5",
	"machine_end_gcode": "M104 S0 ; turn off extruder heating\nM140 S0 ; turn off bed heating\nM107 ; turn off fans\nG91 ; relative positioning\nG0 Z+0.5 ; move Z up a tiny bit\nG90 ; absolute positioning\nG0 X135 Y105 F{machine_max_speed_x[0]*60} ; move extruder to center position\nG0 Z190.5 F{machine_max_speed_z[0]*60} ; lower the plattform to Z min\nM84 ; steppers off\nG90 ; absolute positioning\n",
	"scan_first_layer": "0"
}