* 10-25
Add TPU-95A HF
* 1030
Adding Introduction of Chamber Temperature Control Macros(M191) to Notes
* 1102
Add ABS-GF10 profile，
Remove a extra "s" from the "0.36mm Standard @Qidi XPlus3 0.6 nozzle.json" file
* 1106
Add the PA value to some genetic filament profiles
* Update fdm_filament_pla.json
Change the fan rate of begin layers
* Update fdm_process_qidi_x3_common.json
Reduction of top surface particles
* Update fdm_process_qidi_x3_common.json
Add M140 S90 to M191 macro, Preventing slow chamber warming in cold winter environments
* 10-25
Add TPU-95A HF
* 1030
Adding Introduction of Chamber Temperature Control Macros(M191) to Notes
* 1102
Add ABS-GF10 profile，
Remove a extra "s" from the "0.36mm Standard @Qidi XPlus3 0.6 nozzle.json" file
* 1106
Add the PA value to some genetic filament profiles
* Update fdm_filament_pla.json
Change the fan rate of begin layers
* Update fdm_process_qidi_x3_common.json
Reduction of top surface particles
* Updating voron profiles
* Add missing V0 configs and add default print profiles
* Update nozzle_diameter for v0, switchwire, and triedent
* Correcting names, nozzle diameters, and adding missing min and max layer heights
* Travel very close to the inner holes, could cross external perimeter when the avoid crossing perimeters was enabled.
(cherry picked from commit prusa3d/PrusaSlicer@6c51e5148c)
* Modified variable offset in the avoid crossing perimeters to not cause scars on thin objects (#7699).
Previously, the minimum contour width was chosen too conservative and, on some thin objects, only allowed minimal (or non) offset. This could result in travels being planned along the outer perimeter.
Now, the minimum contour width is chosen much smaller at the start and tested if the variable offset wasn't failed (the outer contour broke up into more parts, more or fewer holes, etc.).
If any problem is detected, the variable offset is recalculated with a larger minimum contour width.
(cherry picked from commit prusa3d/PrusaSlicer@dc00f0bf98)
---------
Co-authored-by: Lukáš Hejl <hejl.lukas@gmail.com>
* 10-25
Add TPU-95A HF
* 1030
Adding Introduction of Chamber Temperature Control Macros(M191) to Notes
* 1102
Add ABS-GF10 profile，
Remove a extra "s" from the "0.36mm Standard @Qidi XPlus3 0.6 nozzle.json" file
* 1106
Add the PA value to some genetic filament profiles
* Update fdm_filament_pla.json
Change the fan rate of begin layers
* Remove retraction_length from common
M5c should never retract more then 0.8mm or it will clog
* Preserve M5 retraction length
Moved previous retraction length from core to M5
* Update Anker M5C retraction length to prevent clogs
Anything beyond a 0.8mm retraction length will clog the printer over time.
* Update OrcaSlicer_zh_TW.po
* update locale for 1.8 beta2
Following the version update of 1.8 beta2, new localizations will be added
* Update OrcaSlicer_zh_TW.po
* Update OrcaSlicer_zh_TW.po
fixed some conflict
* Added correct machine pause code for FlashForge printers
Added machine pause code for Flashforge printers to support pause action in firmware 2.3.6-2.1.9-20231101
* Removed redundant gcodes for Flashforge profiles
Removed redundant gcodes for Flashforge profiles as they are already added by Orca Slicer
* Add back the option to disable `ensure vertical shell thickness` (#2602)
* Add back the option to disable `detect narrow internal solid infill` (#2623)
* 10-25
Add TPU-95A HF
* 1030
Adding Introduction of Chamber Temperature Control Macros(M191) to Notes
* 1102
Add ABS-GF10 profile，
Remove a extra "s" from the "0.36mm Standard @Qidi XPlus3 0.6 nozzle.json" file
* 1106
Add the PA value to some genetic filament profiles
* Update fdm_process_qidi_x3_common.json
The macro code cant add to the bottom of the printer.cfg
