* Change ensure_vertical_shell_thickness to enum value type. Allow users to turn off this feature completely
* add warning to the tooltip for None option
* Allow apply scarf joint seams to perimeters without sharp corners only
* 1. Fix an error when detect whether a loop is smooth
2. Expose scarf_angle_threshold to UI
* fix linux build error
* minor code changes
* Support slowdown speed for scarf joint only
* update tips
* improve the logic a bit
* Fixed a bug that scarf speed may not respected for overhangs
* Add a new scarf flow ratio option
* FIX: Support building with latest Xcode 15.3
Downgrade 'enum-constexpr-conversion' error to warning.
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* FIX: Do not assume libdeflate is not installed on the system
Explicitly disable libdeflate support in TIFF depencency.
PrusaSlicer already does that.
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* FIX: Downgrade enum-constexpr-conversion warning only on AppleClang 15+
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
---------
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* FIX: revert default CMake generator for deps on macOS
Before I wrongfully assumed that default CMake generator for both deps
and slicer is Xcode.
This is not true, as deps used implicitly-defaulted Unix Makefiles.
Fix by separating generator used for Slicer and deps, leaving the
choice to use Ninja for both.
Right now Xcode generator is not supported for deps and must be fixed
separately.
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* FIX: Use ALL_BUILD target when building slicer with Xcode generator
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* FIX: Adjust .app searching subdir for Xcode generator
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
---------
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* ENH: Improve macOS build script
- Update shebang to bash, as it is already expected to be present in
run_gettext.sh
- Added fail-fast shell options.
- Changed default CMake generator to Ninja
- Adopted configuration for non-multi-config generators (Ninja, Make)
- Added new options:
- Allow to set CMake generator back to Xcode, no option for make
thou.
- Allow to build without reconfiguring CMake, improves build times.
Unnecessary Cmake reconfigurations require full rebuild.
- Allow to set build configuration for CMake
- Reorganized targets into separate function to break "cd" dependency.
- Reformat shell code.
- Fix all warnings reported by ShellCheck linter tool.
- Update run_gettext.sh to respect build dir in full mode.
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* FIX: Install ninja with brew on CI.
Test if building works with Ninja by default.
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* ENH: Set Xcode back as default generator.
Use Ninja on CI with explicit option.
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* FIX: Partially revent changes in run_gettext.sh
Revert changes for option parsing.
Leave fixes for issues found by ShellCheck linter tool.
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
---------
Signed-off-by: Dzmitry Neviadomski <nevack.d@gmail.com>
* Remember z of previous layer
* Support travel to middle of the layer z
* Support sloped extrusion
* Implement sloped seam
* Reduce extra movements
* Don't clip loop if sloped seam is enabled
* Fix wipe
* Ensure `slope_max_segment_length`
* Add options
* Limit slope length to perimeter length
* Fix slope segmentation
* Rename the option to scarf joint seam
* Don't modify the slope option when turning on spiral vase
* Add a few suggestions when turnning on scarf joint
* Add option to add scarf joint to inner walls
* Apply seam gap at the end of the slope
* Add option to explicitly use the entire loop as scarf length
* Fix layer number
* Increase default scarf length to 20mm
* Better way of storing the global scarf state
* Better vase mode layer height recognition
* Move id should exclude seams
* Fix slope height with independent support layer height
* Fix linux build
* Allow controlling the scarf with modifier
* Scarf start height default to 0
* Allow enable scarf seam on contour only
* Fix type error
* Move the creation of sloped loop into ExtrusionEntity.cpp
* Fix error "vector too long"
* Detect seams properly
* The correct way of calculating the rate limit
* The correct way of calculating the rate limit
(cherry picked from commit 05961f7c98803a42871b8df855bfff6a102936c4)
* Add pressure equalizer in print by object mode
* Remove the settings recommendation as it varies a lot depends on printer & filament
* Add a beta suffix
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
* The correct way of calculating the rate limit
* Add pressure equalizer in print by object mode
---------
Co-authored-by: SoftFever <softfeverever@gmail.com>
Size dropped 2328KB to 2060KB after changing side surfaces. current model has 3 surfaces for each line on side surface. just redraw a cylinder and rejoined surface. result is exactly same.
It's my first commit. i hope i did right. i choose simpler one for first. i will send more
thanks
* Add .02 nozzle profiles
* Remove carbon fiber 0.2 profiles
* Flag Filament Types Correctly
* Add missing PC 0.2 profile
* Correct PLA nozzle name typo
* Tune supports for the thinner layer lines
* Pull in latest main branch updates
* Correct Support bottom distance
* Correct the numbering
* Add 0.25mm Nozzle Profiles
* Enable manual filament changing for all AnkerMake Printers
* Pull in latest main branch updates
* Remove extra white space from file name
---------
Co-authored-by: Geofrey Ward <Xelinor@mail.com>
Co-authored-by: SoftFever <softfeverever@gmail.com>
